Mesh does not prevent cracking. It controls crack width, holding cracks tight so they stay hairline instead of opening up. That distinction matters, because it explains both when mesh is worth having and why badly positioned mesh does nothing at all.
A shed base on well-compacted ground genuinely does not need it. A driveway carrying a car does.
What mesh actually does
All concrete shrinks as it cures, typically around 0.5mm per metre. The slab is restrained by friction against the sub-base and by its own edges, so it cannot shrink freely. Tensile stress builds, and concrete is weak in tension.
Cracks are therefore inevitable. Control joints decide where they form; mesh decides how wide they get.
Once a crack forms, the steel crossing it holds the two sides together. Instead of a 3mm gap that lets in water and grit, you get a hairline crack that stays closed and largely invisible.
The secondary function is load distribution. Under a wheel load, mesh helps spread the force across a wider area of slab rather than letting it concentrate at one point.
Which slabs need it
| Slab | Mesh? | Specification |
|---|---|---|
| Shed base under 10m² | Optional | A142 if ground is variable |
| Greenhouse base | No | — |
| Garden path | No | — |
| Patio | No | — |
| Slab over 10m² | Yes | A142 |
| Driveway, cars | Yes | A142 |
| Driveway, vans | Yes | A193 |
| Garage floor | Yes | A142 minimum |
| Workshop with machinery | Yes | A193 |
| Hot tub base | Yes | A142 or A193 |
| Slab on clay or made ground | Yes | A142 minimum |
The general rule: mesh where there are concentrated loads, where the slab is large enough that shrinkage stress accumulates, or where the ground underneath is anything other than uniformly firm.
Thickness before reinforcement
If you have a fixed budget and are choosing between a thicker slab and adding mesh, thickness usually wins.
A slab’s resistance to bending goes up with the square of its depth. Going from 100mm to 125mm — a 25% increase in concrete — increases bending resistance by around 56%. Mesh in the middle third adds nothing comparable.
That said, the two are not really in competition on a driveway. The extra 25mm of concrete on a 30m² slab costs more than the mesh does, and the sensible specification is 125mm with A142 rather than 150mm plain.
Mesh is not a fix for a bad sub-base
This is the misconception that costs people money.
A slab bridging a soft spot is loaded in bending, and bending is what cracks concrete. Mesh in the middle of the slab does very little to resist bending, because the tension is at the bottom face where the mesh is not.
If your sub-base is inadequate, adding mesh buys you a slab that cracks anyway and holds the crack slightly tighter. Spending the same money on another 50mm of properly compacted Type 1 is far more effective.
The order of priority is always: sub-base first, thickness second, reinforcement third.
Position is everything
Mesh must sit in the middle third of the slab depth. For a 150mm slab that means 50 to 100mm from the bottom.
Mesh lying on the sub-base is the single most common mistake on DIY slabs, and it achieves nothing whatsoever. Steel at the very bottom of a slab is below the neutral axis for the loads that matter and is also at risk of corroding from ground moisture.
Hooking it up with a rake during the pour — “pulling it up” — does not work either. You cannot control the height, most of it ends up back on the bottom, and you disturb concrete that has already been placed.
Use plastic or concrete chairs at 800mm to 1m centres. They cost pennies each and they are the difference between reinforcement and decoration.
Cover
Steel needs concrete around it to protect it from corrosion. Minimum cover for a domestic slab is 40mm from any face, more in aggressive conditions.
That also means keeping mesh 50mm back from the slab edges. Mesh running to the edge corrodes from the side, and rust expands, which spalls the concrete off.
Mesh versus fibres
Polypropylene fibres mixed into the concrete control plastic shrinkage cracking in the first few hours. They are cheap, need no positioning, and are worth adding to almost any slab.
What they do not do is replace mesh for structural crack control or load distribution. The fibres are short and randomly oriented; they cannot bridge a crack the way a continuous steel bar does.
On a driveway, use mesh. On a driveway where you want the best result, use both.
What it costs
| Item | Cost | For a 30m² driveway |
|---|---|---|
| A142 mesh sheet (4.8 × 2.4m) | £28–£40 | 3 sheets, £84–£120 |
| A193 mesh sheet | £38–£55 | 3 sheets, £114–£165 |
| Chairs | £0.15–£0.30 each | ~40, £6–£12 |
| Tie wire | £8–£12 a roll | 1 roll |
| PP fibres | £8–£15 per m³ | £30–£56 |
Around £100 to £140 on a 30m² driveway, against a total job cost of £3,000 or more. It is not the place to economise.
Work out your slab volume and area with the slab calculator, then allow for mesh sheets with a full square of overlap at every lap.
Laying it out
Lap adjacent sheets by at least one full mesh square, typically 200mm, and tie the laps with wire so they cannot separate during the pour.
Cut mesh with bolt croppers or an angle grinder. Wear gloves — cut mesh ends are genuinely sharp, and a sheet flexes unpredictably as you cut it.
Walk on boards laid across the mesh during the pour rather than directly on it. Standing on mesh pushes it down off its chairs, which puts you straight back to having steel on the sub-base.
Stop the mesh at every control joint rather than running it straight through. A joint is meant to be a plane of weakness where the slab can crack cleanly; continuous steel across it fights that and the crack forms somewhere else instead.
Where mesh must cross a joint — for load transfer between bays — the correct detail is a dowel bar, greased on one side so it transfers vertical load while still allowing the two panels to move apart.
Checking it before the truck arrives
Five minutes with a tape before the concrete comes settles whether the money was spent well:
- Measure from the sub-base to the mesh at half a dozen points — should be a third of the slab depth
- Check the gap between mesh and formwork at every edge — 50mm
- Push down on the mesh between chairs; if it sags more than a few millimetres, add chairs
- Confirm every lap is a full square and tied
- Brush off any mud that has been walked onto the steel
This is the last moment anything can be changed. Once concrete is flowing, the mesh is wherever it happens to be.
Common questions
Does a shed base need mesh?
Usually not, if it is under about 10m² on well-compacted ground. Add A142 if the ground is variable, the base is larger, or anything heavy is going on it.
Where should mesh sit in a slab?
In the middle third of the depth, on chairs. For a 150mm slab that is 50 to 100mm from the bottom. Mesh lying on the sub-base does nothing.
Can I pull the mesh up during the pour?
No. You cannot control the height, most of it settles back down, and you disturb concrete already placed. Use chairs.
Does mesh stop concrete cracking?
No. It controls crack width, keeping cracks hairline rather than open. Control joints decide where cracks form; mesh decides how bad they look.
Is mesh or fibre better?
Different jobs. Fibres control early plastic shrinkage cracking; mesh controls crack width and distributes load over the slab’s life. On a driveway, mesh is the one that matters.